Bantam BC8HP Betriebsanleitung

eSTATION-BC8DXOperating Instructions* We reserve the right to commit modifications.* Copyright reservedTwo identical and independent outputs with inte

eSTATION-Lithium battery (LiIo/LiPo/LiFe) program These programs are only suitable for charging and d

eSTATION-!- Chg. mode (Charge mode) : You can select a method of charging, they are Normal, Balance, FAST. Balance mode; This is for equalizing the i

eSTATION-!!- 12 -!! This is for Lithium battery not to be used for long time. The program will determine to charge or discharge the battery to a certa

eSTATION-!!- 13 -!!V/A/Ahapprox.98%VoltAmpsAhCC(Constant Current)CV(Constant Voltage) These batteries need to adopt different charge technique which i

eSTATION-NiMH/NiCd battery programCharging NiCd/NiMH battery! These programs are for charging or discharging NiMH

eSTATION-!Chg curr : 5.0AChg mode : NormalCurr mode : ManualDelta-peak : 10mV/CMax capa

- Cycle mode : Set the sequence of performing program. CHG&

eSTATION-!!- 17 -Charging Pb batteryPROGRAM SELECTCH2>LiPoLiFeLiIoNiMHNiCdPbSETUPREVIEWChg curr : 5.0AChg volt :

eSTATION-!!- End curr. (End current) : Set the final charging current at termination. Auto; The process will be terminated when the charging curren

eSTATION-!!NiMH 00298mAh CHG13.07V 1.25A 0039:15 ▶End volt : AutoEnd capa : 1210mAhIn volt :

eSTATION-- Operating software The operating program in this charger is executed with mutual links and communications with every components to preve

eSTATION-!!- 20 -▶Review the data after finishing the process(1) Output voltage : Shows the DC voltage at the output on end of process.(2) Charged or

eSTATION-Warning and error messagesThe output is connected to a battery with incorrect polarity.This will be displayed in case of detecting an interru

eSTATION-Glossary of termsAmps(A): The unit of measure for charge or discharge electric current. The program of the charger will show most of the curr

eSTATION-Maximum circuit power chart For the voltage of battery is more than 16V, the actual amount of charge current feeds to the battery might autom

Electrical equipment marked with the cancelled waste bin symbol must not be discarded in the standard household waste; instead it should

eSTATION-Exterior of the charger!!- 3 -- ‘CHANNEL’ button Switches the screen display between output-1 and output-2. The user can see the values fo

eSTATION-Warnings and safety notesNever leave the charge unsupervised when it is connected to its power supply. If any malfunction is observed, termin

eSTATION-Please bear in mind of checking the following point before charge operation. - Did you select the appropriate program, which are suitable fo

Program flow chartLiPo/LiFe/LiIoPROGRAMCHARGEeSTATION-!Charge current0.1~9.0ACharge modeNormal/Balance/FastEnd currentAuto, 60~500mAUPUPDOWNDOWNCheck

eSTATION-!Pb(Lead-acid)PROGRAMCHARGECharge current0.1~9.0ACharge volt2.20~2.50V/cell Charge modeLiner/PulseEnd currentAuto/60~500mAMODEMODEMaximum Cap

eSTATION- Initial parameter set up BC8DX will be operated with the default values of the initial settings which were done at the factory, when it is c

eSTATION-!- In Vol. Low : This program monitors the voltage of input battery. If the voltage drops below the value you set the operation forcibly term